Category Archives: Tinkering

3D print your own dust collector blast gates

Posted on June 3, 2020 by robertwilkie

Nice build. If you have a printer that can handle the size. The “gate” thought is not printed but a piece of plexi glass. Not sure if I would build on of these myself. If my printer could handle it. … Continue reading →

Posted in CNC/3D-printing, Misc-Life, Tools | Comments Off on 3D print your own dust collector blast gates

Awesome Shield build

Posted on June 2, 2020 by robertwilkie

But I don’t know if I would have the patience to make this. The author traces all the patterns on the shield first, then using a dremel in router mode, cuts out the outline, then chisels out chunks, then burns … Continue reading →

Posted in woodworking | Comments Off on Awesome Shield build

Ghetto automatic soap dispenser

Posted on May 21, 2020 by robertwilkie

I got a kick of this build. It does work thought. https://www.instructables.com/id/Automatic-Soap-Dispenser-Using-Arduino/

Posted in Arduino, Cheap, Misc-Life | Comments Off on Ghetto automatic soap dispenser

Cool looking necklace build

Posted on May 21, 2020 by robertwilkie

Nice build, the author posts the schematic so you could get your own board built… Or modify it yourself. https://www.instructables.com/id/NeckLight-a-PCB-Necklace-for-Humans-and-Dogs/

Posted in Tinkering | Comments Off on Cool looking necklace build

Cool looking wall art

Posted on May 19, 2020 by robertwilkie

Interesting build. One thing I might do differently is put an inner set of LED strips too. https://www.instructables.com/id/Wooden-Neopixel-Hexagon/

Posted in Arduino, Cheap, Misc-Life | Comments Off on Cool looking wall art

Improved Spline Jig

Posted on May 18, 2020 by robertwilkie

I think I showed the original one a few months back. Well the author went back on the build and made a better version of it. It looks nice. https://www.homemadetools.net/forum/%93no-clamps%94-spline-jig-w-folding-knobs-78449?homelistings#post154771

Posted in Cheap, Misc-Life, Tools, woodworking | Comments Off on Improved Spline Jig

3D print a face mask

Posted on May 17, 2020 by robertwilkie

I have seen a couple of different versions of this one. Not so sure how comfortable this is, or how porious a 3D printed object could be…. https://www.instructables.com/id/3D-Printed-COVID-19-Mask-With-Gasket/

Posted in CNC/3D-printing, Misc-Life | Comments Off on 3D print a face mask

3D print your own frame for a face visor

Posted on May 16, 2020 by robertwilkie

Nice write up on how to setup the Prusa face visor (uses a transparency). Unfortunately the table on my printer is a touch too small for this one. https://www.instructables.com/id/DIY-Rc2-Visor-and-Face-Shields/

Posted in CNC/3D-printing, Misc-Life | Comments Off on 3D print your own frame for a face visor

Make your own carbon filters

Posted on May 15, 2020 by robertwilkie

I have this on my list to make. I own a 3M Respirator and right now replacement filters are expensive. Of course same issue with other 3D printed items, particles could still get inside thru the print. But it could … Continue reading →

Posted in Cheap, CNC/3D-printing, Misc-Life | Comments Off on Make your own carbon filters

Make a Wuhan Hook

Posted on May 15, 2020 by robertwilkie

This is too funny, basically its a door opener (for doors with latch handles). Once you open the door, you hit the lighter to burn up an possible contaminates. The base is 3D printed. https://www.instructables.com/id/Wuhan-Hook-V2-Simple-Self-Disinfecting-Wand-to-Pre/

Posted in Cheap, CNC/3D-printing, Misc-Life | Comments Off on Make a Wuhan Hook