Category Archives: Misc-Life

Interesting food processor build

Posted on July 6, 2020 by robertwilkie

The author took a grinder, and 2 metal cans to make a food processor. Interesting build…not so sure why he didn’t use a food processor (I think you can get ones for $20 that are decent). Either way with the … Continue reading →

Posted in Cheap, Misc-Life | Comments Off on Interesting food processor build

Interesting birdhouse build

Posted on July 3, 2020 by robertwilkie

Could be a nice way to make one and eliminate some of the wood needed for the floor. Actually I think I would paint the can myself, and stain or paint the wood. But its a nice build overall. https://www.instructables.com/id/Coffee-Can-Birdhouse/

Posted in Cheap, Misc-Life, woodworking | Comments Off on Interesting birdhouse build

Simple automatic soap dispenser

Posted on July 2, 2020 by robertwilkie

Using an arduino, IR sensor, and a servo, the author built a pretty simple conversion for a pump action soap dispenser. Could be a simple project to do with kids. https://www.instructables.com/id/Automatic-Soap-Dispenser-Using-Arduino/

Posted in Arduino, Cheap, Misc-Life | Comments Off on Simple automatic soap dispenser

Make your own rav Marshmellow head

Posted on June 30, 2020 by robertwilkie

Nice build, the bucket used is a good idea. LED’s are a bit pricy for the project (individual addressed LED’s are not cheap). https://www.instructables.com/id/Marshmello-Ultimate-Head-With-Programmable-Bluetho/

Posted in Cheap, Misc-Life | Comments Off on Make your own rav Marshmellow head

Nice 3D printed stand for an electronic mircoscope

Posted on June 29, 2020 by robertwilkie

The author made this build for a scope based webcam that he could hold a circuit board down on and solder components too. Me…yeah I don’t go that small in boards (and usually use thru hole). But I could see … Continue reading →

Posted in Cheap, CNC/3D-printing, Misc-Life | Comments Off on Nice 3D printed stand for an electronic mircoscope

nice multi angle table saw jig

Posted on June 26, 2020 by robertwilkie

This can be used not just for angled cuts, but to “straighten” out boards that have a curve to them. Relatively simple build too. https://www.homemadetools.net/forum/4-1-multi-adjustable-table-saw-jig-78635?homelistings#post155545

Posted in Cheap, Misc-Life, Tools, woodworking | Comments Off on nice multi angle table saw jig

Nice portable water sprayer

Posted on June 25, 2020 by robertwilkie

Good way to wash off dogs or yourself. It uses a weed sprayer bottle, and a shower head extension. The one bit I got that was interesting is the incoming tube in the sprayer may have restrictors in them that … Continue reading →

Posted in Cheap, Misc-Life | Comments Off on Nice portable water sprayer

Nice build for a roller stand

Posted on June 24, 2020 by robertwilkie

Very nice build. A bit more work than I would do thought. https://www.homemadetools.net/forum/easy-diy-adjustable-3-rolls-outfeed-stand-%7C-free-plans-79885?homelistings#post160084

Posted in Cheap, Misc-Life, Tools | Comments Off on Nice build for a roller stand

Another nice build for a pocket hole jig

Posted on June 22, 2020 by robertwilkie

Nice build done with mostly hand tools and a table saw https://www.homemadetools.net/forum/pocket-hole-jigs-diy-pocket-hole-drill-bit-79869?homelistings#post160016

Posted in Cheap, Misc-Life, Tools | Comments Off on Another nice build for a pocket hole jig

Using a conrete paver and foam for a stand for your 3D printer

Posted on June 19, 2020 by robertwilkie

Interesting build, the paver gives some stability, and the foam helps dampen the vibrations. https://blog.adafruit.com/2020/05/19/the-best-2-upgrade-for-your-3d-printer-3dprinting/

Posted in Cheap, CNC/3D-printing, Misc-Life | Comments Off on Using a conrete paver and foam for a stand for your 3D printer