Interesting LED haloween sign

Posted on September 1, 2020 by robertwilkie

The base is 3D printed and the author “grinds” the shape/pattern on plexiglass (after printing out a template). INteresting build, I like how it has the battery compartment built in the print.

https://www.instructables.com/id/3D-Printed-Plexiglass-LED-Sign/
Posted in Cheap, CNC/3D-printing, Misc-Life | Comments Off on Interesting LED haloween sign

Nice lowrider CNC

Posted on August 31, 2020 by robertwilkie

Nice lowrider CNC build (build to do sheets of plywood. It cost the author roughly $650 in materials and parts.

https://www.instructables.com/id/Fliptable-LowRider-CNC/

https://www.thingiverse.com/thing:3026040

Posted in Cheap, CNC/3D-printing, Misc-Life | Comments Off on Nice lowrider CNC

Nice book light

Posted on August 28, 2020 by robertwilkie

I was thinking this build may make a good costume item for say a wizard for halo ween.

https://www.instructables.com/id/LED-Book-Light-Inside-a-Book/

Posted in Cheap, Misc-Life | Comments Off on Nice book light

Another CDROM CNC build

Posted on August 27, 2020 by robertwilkie

This build is a bit interesting, as it uses the base of the original CDROM, but the Y is a 3D printed part with the motor. I like the Y and Z part of this build, may have to save that bit for later.

https://www.instructables.com/id/Drawing-Robot-With-Adafruit-Shield-Make-It-Move-Co/

Posted in Arduino, Cheap, CNC/3D-printing, Misc-Life | Comments Off on Another CDROM CNC build

Business card embosser

Posted on August 27, 2020 by robertwilkie

Interesting build, basically you 3D print your design, then roll a business card thru it to make an indention design on the paper.

https://www.instructables.com/id/The-Business-Card-Embosser-System/

Posted in Cheap, CNC/3D-printing, Misc-Life | Comments Off on Business card embosser

Nice lamp build from plywood

Posted on August 26, 2020 by robertwilkie

Nice build, the author uses a combo of handtools and CNC to make this.

https://www.instructables.com/id/Mid-Century-Flexible-Plywood-Lamp/

Posted in Cheap, CNC/3D-printing, Misc-Life, woodworking | Comments Off on Nice lamp build from plywood

Nice cross cut table for circular saws

Posted on August 25, 2020 by robertwilkie

Nice built, I love out the author goes over his mistakes at the end. I also like his router circle jig.

https://www.homemadetools.net/forum/super-simple-cheap-table-saw-alternative-%7C-free-plans-81040?homelistings#post164655

Posted in Cheap, Misc-Life, Tools | Comments Off on Nice cross cut table for circular saws

Another nice LED light build

Posted on August 24, 2020 by robertwilkie

This one is with RGB strips so you can get some variety of color on the subject.

https://www.instructables.com/id/Build-a-Pocket-RGB-LED-Light-for-Your-Home-Photo-S/

Posted in Cheap, Misc-Life | Comments Off on Another nice LED light build

Installing a downspout or sump pump drywell

Posted on August 21, 2020 by robertwilkie

I have thought about doing this myself as the clay lines for my gutters are breaking down. Hard part is I can only dig in the yard in spring or fall (clay soil) and when its dry, its harder than a rock.

https://www.instructables.com/id/How-to-Install-a-DownspoutSump-Drywell-to-Reduce-F/

Posted in Cheap, Misc-Life | Comments Off on Installing a downspout or sump pump drywell

Simple “shield” for tutoring students

Posted on August 21, 2020 by robertwilkie

Its a simple plexiglass stand for a teacher to put between them and the student for tutoring. Nice build overall, I think the author should put a handle on it too so it can be carried around.

https://www.instructables.com/id/DIY-Teacher-Desk-Shield-for-Writing-Conferences/

Posted in Cheap, Misc-Life, Teaching and Learning | Comments Off on Simple “shield” for tutoring students