-
Archives
- January 2024
- October 2023
- September 2023
- August 2023
- June 2023
- May 2023
- April 2023
- March 2023
- February 2023
- January 2023
- December 2022
- November 2022
- October 2022
- September 2022
- August 2022
- April 2022
- March 2022
- February 2022
- January 2022
- December 2021
- November 2021
- October 2021
- September 2021
- August 2021
- July 2021
- June 2021
- May 2021
- April 2021
- March 2021
- February 2021
- January 2021
- December 2020
- November 2020
- October 2020
- September 2020
- August 2020
- July 2020
- June 2020
- May 2020
- April 2020
- March 2020
- February 2020
- January 2020
- December 2019
- November 2019
- October 2019
- September 2019
- August 2019
- July 2019
- June 2019
- May 2019
- April 2019
- March 2019
- February 2019
- January 2019
- December 2018
- November 2018
- October 2018
- September 2018
- August 2018
- July 2018
- June 2018
- May 2018
- April 2018
- March 2018
- February 2018
- January 2018
- December 2017
- November 2017
- October 2017
- September 2017
- August 2017
- July 2017
- June 2017
- May 2017
- April 2017
- March 2017
- February 2017
- January 2017
- December 2016
- November 2016
- October 2016
- September 2016
- August 2016
- July 2016
- June 2016
- May 2016
- April 2016
- March 2016
- February 2016
- January 2016
- December 2015
- November 2015
- October 2015
- September 2015
- August 2015
- July 2015
- June 2015
- May 2015
- April 2015
- March 2015
- February 2015
- January 2015
- December 2014
- November 2014
- October 2014
- September 2014
- August 2014
- July 2014
- June 2014
- May 2014
- April 2014
- March 2014
- February 2014
- January 2014
- December 2013
- November 2013
- October 2013
- September 2013
- August 2013
- July 2013
- June 2013
- May 2013
- April 2013
- March 2013
- February 2013
- January 2013
- December 2012
- November 2012
- October 2012
- September 2012
- August 2012
- July 2012
- June 2012
- May 2012
- April 2012
-
Meta
Monthly Archives: September 2021
Interesting multi-purpose table saw jig
I had to look this over a couple of times before I saw all the different functions it could do. I do like the overall build, seems a bit time consuming to make thought. https://www.homemadetools.net/forum/3-1-table-saw-multi-jig-86700?homelistings#post186322
Nice Robot gripper
This one uses belts to pull and grip objects.
Generating power as your ride your bike
Basically has the same build as a homemade wind generator, with a disk with magnets on them, and coils inside the spinning magnet hubs to charge everything. Its an interesting build, not so sure I would do it (need to … Continue reading
Solar trickle charger thru OBD-II reader for car
I have thought about this myself during COVID lockdown where after a month or two of my car sitting still, the battery was pretty weak.
A simple router table build
The author make a simple router table build, with accessories. Pretty straight forward build too.
Another porch pirate preventor build
This time from a Canadian, who tried to build a prevention instead of the revenge based ones. I like the logic he put in to determine if a package was dropped off and to arm the system. https://www.tomshardware.com/news/raspberry-pi-package-security-system
Posted in Cheap, Misc-Life, RaspberryPi
Comments Off on Another porch pirate preventor build
POT to PWM controller
Using an ATiny no less, bascially you turn the POT, and a PWM comes out to control the motor speed. Good for DC based motors. It also has a nice small footprint. https://www.instructables.com/Poti-PWM-Control/
Clever strap harness for walking multiple dogs
I only have 2, and I know that can be a challenge, so I like this strap build. My 2 cents, not sure if I would put the clips lower incase the dogs all see something to play with and … Continue reading
Nice jig for a Kreg R3
Actually I could see making something like this for the smaller single slot Kreg as well. Basically it turns the R3 into its a big brother pocket hole jig. https://www.instructables.com/Pimped-Kreg-R3-Jig/
Well thats one way to pull out a stump
The author uses a metal bar, a jack, and a fulcrum to pull stumps out. Good example of using a lever to do work! https://www.homemadetools.net/forum/car-jack-stump-puller-video-86540?homelistings#post185753